String.equals()
Description
Compare l'égalité de deux objets String. La comparaison est sensible à la casse, ainsi le String "hello" n'est pas égal au String "HELLO".
Syntaxe
string.equals(string2)
Valeurs Renvoyées
- true: si l'objet string est égal à l'objet string2
- false: si ce n'est pas le cas
Exemple
String stringOne, stringTwo;
void setup() {
Serial.begin(9600);
stringOne = String("this");
stringTwo = String("that");
Serial.println("\n\nComparing Strings:");
}
void loop() {
// two strings equal:
if (stringOne == "this") {
Serial.println("StringOne == \"this\"");
}
// two strings not equal:
if (stringOne != stringTwo) {
Serial.println(stringOne + " =! " + stringTwo);
}
// two strings not equal (case sensitivity matters):
stringOne = "This";
stringTwo = "this";
if (stringOne != stringTwo) {
Serial.println(stringOne + " =! " + stringTwo);
}
// you can also use equals() to see if two strings are the same:
if (stringOne.equals(stringTwo)) {
Serial.println(stringOne + " equals " + stringTwo);
}
else {
Serial.println(stringOne + " does not equal " + stringTwo);
}
// or perhaps you want to ignore case:
if (stringOne.equalsIgnoreCase(stringTwo)) {
Serial.println(stringOne + " equals (ignoring case) " + stringTwo);
}
else {
Serial.println(stringOne + " does not equal (ignoring case) " + stringTwo);
}
// a numeric string compared to the number it represents:
stringOne = "1";
int numberOne = 1;
if (stringOne == numberOne) {
Serial.println(stringOne + " = " + numberOne);
}
// two numeric strings compared:
stringOne = "2";
stringTwo = "1";
if (stringOne >= stringTwo) {
Serial.println(stringOne + " >= " + stringTwo);
}
// comparison operators can be used to compare strings for alphabetic sorting too:
stringOne = String("Brown");
if (stringOne < "Charles") {
Serial.println(stringOne + " < Charles");
}
if (stringOne > "Adams") {
Serial.println(stringOne + " > Adams");
}
if (stringOne <= "Browne") {
Serial.println(stringOne + " <= Browne");
}
if (stringOne >= "Brow") {
Serial.println(stringOne + " >= Brow");
}
// the compareTo() operator also allows you to compare strings
// it evaluates on the first character that's different.
// if the first character of the string you're comparing to
// comes first in alphanumeric order, then compareTo() is greater than 0:
stringOne = "Cucumber";
stringTwo = "Cucuracha";
if (stringOne.compareTo(stringTwo) < 0 ) {
Serial.println(stringOne + " comes before " + stringTwo);
}
else {
Serial.println(stringOne + " comes after " + stringTwo);
}
delay(10000); // because the next part is a loop:
// compareTo() is handy when you've got strings with numbers in them too:
while (true) {
stringOne = "Sensor: ";
stringTwo = "Sensor: ";
stringOne += analogRead(A0);
stringTwo += analogRead(A5);
if (stringOne.compareTo(stringTwo) < 0 ) {
Serial.println(stringOne + " comes before " + stringTwo);
}
else {
Serial.println(stringOne + " comes after " + stringTwo);
}
}
}
Voir Également
- Langage: Arduino - String
- Langage: String.charAt()
- Langage: String.compareTo()
- Langage: String.concat()
- Langage: String.endsWith()
- Langage: String.equalsIgnoreCase()
- Langage: String.getBytes()
- Langage: String.indexOf()
- Langage: String.lastIndexOf()
- Langage: String.length()
- Langage: String.replace()
- Langage: String.setCharAt()
- Langage: String.startsWith()
- Langage: String.substring()
- Langage: String.toCharArray()
- Langage: String.toLowerCase()
- Langage: String.toUpperCase()
- Langage: String.trim()
※ ARDUINO BUY RECOMMENDATION
| Arduino UNO R3 Buy on Amazon | |
| Official Arduino Starter Kit Buy on Amazon | |
| ELEGOO UNO R3 Starter Kit Buy on Amazon |
Please note: These are affiliate links. If you buy the components through these links, We may get a commission at no extra cost to you. We appreciate it.
Follow Us