continue
Descrição
O comando continue "pula" o resto da iteração atual de um loop (for, while, ou do...while). Esse comando continua a checar a expressão condicional do loop, e procede com qualquer iterações subsequentes.
Código de Exemplo
Example with For Loop
Example 1
The following code exits the for loop when the i greater than 3
void setup() {
Serial.begin(9600);
Serial.println("====== TEST START ======");
for (int i = 1; i < 5; i++) {
Serial.print("Inside the FOR loop: i = ");
Serial.print(i);
Serial.println(", start");
if(i > 2)
continue;
Serial.print("Inside the FOR loop: i = ");
Serial.print(i);
Serial.println(", end");
}
Serial.println("====== TEST END ========");
}
void loop() {}
The result on Serial Monitor:
8
Serial.println("Hello World!");
Message (Enter to send message to 'Arduino Uno' on 'COM15')
New Line
9600 baud
====== TEST START ======
Inside the FOR loop: i = 1, start
Inside the FOR loop: i = 1, end
Inside the FOR loop: i = 2, start
Inside the FOR loop: i = 2, end
Inside the FOR loop: i = 3, start
Inside the FOR loop: i = 4, start
====== TEST END ========
Example 2
O código abaixo escreve o valor de 0 a 255 ao pino PWMpin, mas pula os valores no intervalo 41 a 119.
for (int x = 0; x <= 255; x ++) {
if (x > 40 && x < 120) { // cria um salto nos valores
continue;
}
analogWrite(PWMpin, x);
delay(50);
}
Example with While Loop
The following code exits the while loop when the i greater than 3
void setup() {
Serial.begin(9600);
Serial.println("====== TEST START ======");
int i = 0;
while (i < 5) {
i++; // increase i by 1
Serial.print("Inside the WHILE loop: i = ");
Serial.print(i);
Serial.println(", start");
if(i > 2)
continue;
Serial.print("Inside the WHILE loop: i = ");
Serial.print(i);
Serial.println(", end");
}
Serial.println("====== TEST END ========");
}
void loop() {
}
The result on Serial Monitor:
8
Serial.println("Hello World!");
Message (Enter to send message to 'Arduino Uno' on 'COM15')
New Line
9600 baud
====== TEST START ======
Inside the WHILE loop: i = 1, start
Inside the WHILE loop: i = 1, end
Inside the WHILE loop: i = 2, start
Inside the WHILE loop: i = 2, end
Inside the WHILE loop: i = 3, start
Inside the WHILE loop: i = 4, start
====== TEST END ========
Example with Do While Loop
The following code exits the while loop when the i greater than 3
void setup() {
Serial.begin(9600);
Serial.println("====== TEST START ======");
int i = 0;
do {
i++; // increase i by 1
Serial.print("Inside the DO WHILE loop: i = ");
Serial.print(i);
Serial.println(", start");
if(i > 2)
continue;
Serial.print("Inside the WHILE loop: i = ");
Serial.print(i);
Serial.println(", end");
} while (i < 5);
Serial.println("====== TEST END ========");
}
void loop() {
}
The result on Serial Monitor:
8
Serial.println("Hello World!");
Message (Enter to send message to 'Arduino Uno' on 'COM15')
New Line
9600 baud
====== TEST START ======
Inside the DO WHILE loop: i = 1, start
Inside the DO WHILE loop: i = 1, end
Inside the DO WHILE loop: i = 2, start
Inside the DO WHILE loop: i = 2, end
Inside the DO WHILE loop: i = 3, start
Inside the DO WHILE loop: i = 4, start
====== TEST END ========
Ver Também
- Linguagem : break
- Linguagem : do...while
- Linguagem : else
- Linguagem : for
- Linguagem : goto
- Linguagem : if
- Linguagem : return
- Linguagem : switch...case
- Linguagem : while
※ ARDUINO BUY RECOMMENDATION
| Arduino UNO R3 | |
| Arduino Starter Kit |
Disclosure: Some links in this section are Amazon affiliate links. If you make a purchase through these links, we may earn a commission at no extra cost to you.
Additionally, some links direct to products from our own brand, DIYables .
Additionally, some links direct to products from our own brand, DIYables .